Effect of Tooth Tip Circular Radius of Spiral Bevel Gear on Tooth Root Bending
There are three aspects to consider when designing the tip radius: (1) No interference occurs in the running process of […]
Scientific
Scientific
Scientific
Tooth surface equation of bevel gear without backlash
Take the point on the center line as the coordinate origin, fix the base vectors of the coordinate systems S0
Scientific
Effect of Variation of Tooth Thickness of Helical Bevel Gear on Stress of Gear Pair
Tooth thickness is an important parameter for balancing the fatigue life of large and small wheels.Since the number of small
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and
Scientific
Design example of bevel gear tooth surface without backlash
Use CAD software to build accurate 3D model of linear bevel gear pair, as shown in the figure. By substituting
Scientific
Profile of bevel gears with concave convex contact surface without backlash
The tooth profile of the driving and driven section of the linear gear pair is shown in the figure. The
Scientific
Fatigue bearing capacity of helical bevel gears
Bending fracture of teeth and pitting and flaking of tooth surface are the two most common failure modes of main
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and
Scientific
Analysis on the coincidence degree of bevel gears without backlash
The linear gear can also improve the transmission stability by increasing the degree of coincidence. The calculation formula of line
Scientific
Establishing conjugate contact line of bevel gear without backlash
Establish the right-hand coordinate system, as shown in Figure 1. S (o-xyz) and S (oxpypzp) are the main and driven
Scientific
Special testing principle of vibration of fixed-shaft gear drive system
(1) Acceleration signal testing principle A three-way acceleration sensor is installed at 180 degrees intervals on the same circumference of
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System 2
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and
Scientific
Optimization of tooth profile modification for helical gears to reduce impact of meshing
1 Construction of modified tooth surface The modified tooth surface is constructed by superposition of theoretical tooth surface and modified
Scientific
Innovation in Research on Nonlinear Dynamics of Involute Spur Gear Drive System
The innovations of the research work can be summarized as follows: (1) The coupling relationship between the acting direction of
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System 1
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and
Scientific
Calculation of Rolling Impact of Helical Gear
The calculation of impact force in this paper is based on the principle of energy conservation at the moment of
Scientific
Analysis on Dynamic Characteristics of Gears with Different Machining Dynamic Balance Accuracy
Balancing is a process that improves the mass distribution of the rotor to ensure that the vibration or vibration force
Scientific
Different gear machining accuracy of vehicle gear drive system
In theory, the higher the gear machining accuracy level, the better the dynamic performance of the gear drive system, but
Scientific
Dynamic Stress of Drive Shaft of Vehicle Gear Drive System
The bending and torsional vibration displacements of the concentrated mass points on each drive shaft obtained by simulation are taken
Scientific
Bearing Support Reaction of Vehicle Gear Drive System
Bearing is the main component connecting the gear drive system and the box. Under the action of bearing support reaction,
Scientific
Load sharing factor of vehicle gear planetary drive
Under gear 1-8, the load-sharing coefficient of the loaded planetary row is shown in the figure, in gear 1-4, the
Scientific
No load gear dynamic load of vehicle gear transmission system
Previous studies have shown that the sound pressure of air radiation generated by no-load knocking of gears is proportional to
Scientific
Effect of Tooth Side Clearance and Center Distance Deviation of Involute Spur Gear on Dynamic Load
In gear meshing drive, in order to avoid jamming, clearance between tooth profiles must be left, which is an important
Scientific
Two parameter optimization design of involute straight tooth profile modification
The modification parameters of the two gears are the same, the value range of the modification amount is [0, 0.022mm],
Scientific
Time-varying meshing stiffness calculation of gear with cracks
Gao Yun used the finite element method to analyze the stress of gear, determined the position of the maximum principal
Scientific
Influence of Modification Types on Static Characteristics of Involute Spur Gear Drive System
The modification quantity is 0.22mm and the length is 2.8mm. The modification types are linear modification, parabolic modification and conic
Scientific
Effect of Profile Modification of Involute Spur Gear on Tooth Strength
In the research of tooth profile modification, the influence of tooth profile modification on the strength of gear teeth is
Scientific
Effect of profile modification on dynamic load of involute spur gear under different profile modification lengths
With parabolic modification, the dynamic load coefficient changes with the modification amount under different modification lengths as shown in the
Scientific
The influence of the modification amount on the dynamic load of the involute spur gear transmission system with different modification length
Linear modification is adopted, and the value range of modification amount is [0, 0.05mm], and the value interval is 0.002mm.
Scientific
Modified tooth surface of helical gear under heavy load
TE at small wheel φ1A is smaller than LTE under larger load, indicating that the gap between teeth is not
Scientific
Test principle for vibration characteristics of planetary gear drive system
(1) Ring gear root strain test principle Eight teeth are selected as measuring points on the end face of ring
Scientific
Influence of External Load Change of Involute Spur Gear Transmission on Static Characteristics of Modified Gear
Linear modification is adopted with the modification quantity of 0.022m m and the length of 2.8m M. Fixed torque of
Scientific
Influence of Modification Length of Involute Spur Gear Drive System on Static Characteristics
Linear shape modification is adopted with the amount of 0.022mm. The value range of the length of the modification is
Scientific
Influence of Modification Amount on Static Characteristics of Involute Spur Gear Drive System
Linear shape modification is adopted with the length of 2.8mm and the value range of modification is [0.01mm, 0.09mm]. The
Scientific
Calculation of meshing stiffness and relative speed of helical gear meshing points
The meshing stiffness of the rodent point can be calculated by LTCA. The basic idea is to increase the load
Scientific
Profile modification length of involute spur gear drive system
In the research of profile modification based on static characteristics, the selection criteria of profile modification length mostly adopt the
Scientific
Research on Dynamic Characteristics of Gear Drive System under Steady State Conditions
Steady state condition refers to the condition under which the vehicle travels at a constant speed in a certain position
Scientific
Analysis Method for Nonlinear Dynamic Characteristics of Involute Spur Gear
There may be four kinds of motion forms in gear transmission non-linear system: periodic motion, double periodic motion, quasi-periodic motion
Scientific
Effect of No-load Speed of Involute Spur Gear on Dynamic Load
Under no-load condition, gear has two-sided impact phenomena and frequently falls out of teeth. Maximum dynamic meshing force and root
Scientific
Time-varying meshing stiffness calculation of healthy gears
The potential energy method is used to solve the time-varying meshing stiffness of gears.Each tooth is considered as a variable
Scientific
Research on characteristics of gear knocking under no-load condition
To simulate the no-load knocking characteristics of gears, an angular acceleration excitation is applied in the torsional direction of the
Scientific
Effect of Center Distance Deviation of Gear Drive System on Dynamic Load under Steady State Conditions
During machining and assembling of gear drive system, there is deviation between actual and theoretical center distance of gear due
Scientific
Effect of Engine Speed of Gear Drive System on Dynamic Load under Steady State Conditions
Under steady-state conditions, the engine speed range of heavy-duty vehicles studied ranges from 1000 r/min to 4200 r/min.Under full throttle
Scientific
Research on Dynamic Characteristics of Involute Spur Gear Drive System
Vibration characteristics of two-stage fixed-shaft gear drive system and single-stage planetary gear drive system were tested, and the correctness of
Scientific
Modeling of gear drive system with cracks
The centralized parameter method is used to establish the dynamic model of gear transmission system.This method has a small amount
Scientific
Test device and system for vibration characteristics of planetary gear drive system
Taking single-stage planetary gear drive as test object, vibration characteristics test is carried out on the special test bench for
Scientific
Dynamic Model of Involute Spur Gear Drive System Fixed Shaft Gear Drive System
The bearings and gears are simplified as concentrated mass points and the rolling bearings are simplified as isotropic elastic supports.A
Scientific
Data Processing Method for Strain Signal of Involute Spur Gear Drive System
1.The cut-off frequency of low-pass filtering for strain test data is 3kHz of sampling frequency of dynamic strain gauge. 2.As
Scientific
Effect of Gear Modification Coefficient on Gear Slip Rate
To analyze the influence of gear displacement coefficient, it should be divided into equal displacement, unequal positive displacement and unequal
Scientific
Comparative analysis of torsional shear stress of involute spur gear
According to the test results of torsional shear strain of drive shaft, the torsional shear stress is calculated by formula
Scientific
Effect of Helical Bevel Gear Cutter Modification on Tooth Root Bending Stress
In order to improve the bending strength of the small gear root, the heavy contact area is usually designed to
Scientific
Optimization of Spiral Bevel Gear Based on Tooth Height Factor
The tooth height coefficient of hypoid gear pair mainly includes working tooth height coefficient and tooth crest height coefficient, which
Scientific
Data Processing Method for Displacement Signal of Involute Spur Gear Drive System
The transverse displacement test principle of the drive shaft is shown in the figure.O-point is the center position of the
Scientific
Comparison and analysis of vibration and displacement of involute spur gear drive
According to the test results of transverse vibration displacement of transmission, the displacement of axle in test direction is calculated
Scientific
Effect of Gear Modulus and Pressure Angle on Gear Slip Rate
Figure 1 shows the variation trend of sliding rate with gear modulus in standard drives with the number of teeth
Scientific
Comparison and analysis of acceleration of involute spur gear drive system
Torsional angular acceleration of gears 1 and 4 can be obtained by substituting acceleration test results of each gear into
Scientific
Data Processing for Nonlinear Dynamic Acceleration Signal of Involute Spur Gear Drive System
1.The acceleration test signal is filtered with low-pass filter whose cut-off frequency is 10kHz, the highest response frequency of the
Scientific
Contact relationship and stress distribution of flexible ring gear of Involute Harmonic Gear
Flexible ring gear is a spur cylindrical external gear, and the ring gear after assembly deformation presents straight bus deformation
Scientific
Involute Harmonic Gear Flexible Gear Profile Parameters
1. Basic profile parameters and definitions Taking the involute profile as an example, the figure is an illustration of the
Scientific
Nonlinear dynamic backlash and meshing stiffness of sun gear
The analysis process of the dynamic backlash of the outer meshing pair composed of the sun wheel and the star