Tooth surface equation of bevel gear without backlash
Take the point on the center line as the coordinate origin, fix the base vectors of the coordinate systems S0 […]
Scientific
Scientific
Effect of Variation of Tooth Thickness of Helical Bevel Gear on Stress of Gear Pair
Tooth thickness is an important parameter for balancing the fatigue life of large and small wheels.Since the number of small […]
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and […]
News
Gear Blank Selection for Double Drive Gears
1. Material Selection of Blank The mechanical gear blank is simple in structure and small in size, and it has […]
Scientific
Design example of bevel gear tooth surface without backlash
Use CAD software to build accurate 3D model of linear bevel gear pair, as shown in the figure. By substituting […]
Scientific
Profile of bevel gears with concave convex contact surface without backlash
The tooth profile of the driving and driven section of the linear gear pair is shown in the figure. The […]
Scientific
Fatigue bearing capacity of helical bevel gears
Bending fracture of teeth and pitting and flaking of tooth surface are the two most common failure modes of main […]
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and […]
News
Machining technology of double drive gear
The blank is determined to be abrasive forging. After cleaning, the blank is positive-heat quenched and ground to effectively eliminate […]
Scientific
Analysis on the coincidence degree of bevel gears without backlash
The linear gear can also improve the transmission stability by increasing the degree of coincidence. The calculation formula of line […]
Scientific
Establishing conjugate contact line of bevel gear without backlash
Establish the right-hand coordinate system, as shown in Figure 1. S (o-xyz) and S (oxpypzp) are the main and driven […]
Scientific
Special testing principle of vibration of fixed-shaft gear drive system
(1) Acceleration signal testing principle A three-way acceleration sensor is installed at 180 degrees intervals on the same circumference of […]
News
Positioning Elements for Machining Helical Bevel Gears
The locating elements for spiral bevel gears are V-shaped blocks and press plates. After positioning the workpiece, before drilling, it […]
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System 2
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and […]
Scientific
Optimization of tooth profile modification for helical gears to reduce impact of meshing
1 Construction of modified tooth surface The modified tooth surface is constructed by superposition of theoretical tooth surface and modified […]
News
Bevel gear without backlash
Gear is an important basic component in mechanical transmission. Different from other types of gears, bevel gear, as a special […]
News
Basic Requirements for Helical Bevel Gear Locating Elements
The positioning of the workpiece is achieved by the contact between the positioning surface on the workpiece and the V-block […]
Scientific
Innovation in Research on Nonlinear Dynamics of Involute Spur Gear Drive System
The innovations of the research work can be summarized as follows: (1) The coupling relationship between the acting direction of […]
Scientific
Research on Nonlinear Dynamics of Involute Spur Gear Drive System 1
Nonlinear dynamic model of yaw-torsion coupling was established for involute spur fixed-shaft gear drive and planetary gear drive respectively, and […]
News
Research Significance of Cold Extrusion Finishing of Cylindrical Gear by Hot Precision Forging
Compared with traditional cutting process, the hot precision forging cold extrusion compound forming process has the advantages of high efficiency, […]
News
Advantages of Plastic Forming for Cylindrical Gears
The advantages of forming cylindrical gears by plastic forming are as follows: 1) Productivity.Taking the small module gear used in […]
News
Composite Forming of Cylindrical Spur Gear by Hot Precision Forging and Cold Extrusion
Gears are wheel-shaped mechanical parts that transmit torque by whistling closure of teeth.Gears can change speed and torque, direction of […]
Scientific
Calculation of Rolling Impact of Helical Gear
The calculation of impact force in this paper is based on the principle of energy conservation at the moment of […]
News
High-speed heavy-duty gear drive
Gear drive system is widely used in various mechanical equipment because of its accurate transmission ratio, stable and reliable, long […]
News
Gear drive system is the core mechanism of mechanical equipment
Gear drive system is the core mechanism of mechanical equipment and the main equipment to determine the performance of the […]
News
Determination of Process Route for Helical Bevel Gear
Process analysis: The processing of spiral bevel gears is mainly divided into the following stages: 1) Billet processing: Billet forming […]
News
Future Research on Nonlinear Dynamics of Involute Spur Gear Drive System
(1) Deep analysis of tooth bias torque caused by deformation of drive shaft and bearing and tooth error is introduced […]
News
Research on Dynamic Characteristics and Optimum Design of Gear Drive System of Tracked Vehicle
For tracked vehicle gear drive system, firstly, the dynamic loads of main components in different gears are compared and analyzed; […]
Scientific
Analysis on Dynamic Characteristics of Gears with Different Machining Dynamic Balance Accuracy
Balancing is a process that improves the mass distribution of the rotor to ensure that the vibration or vibration force […]
Scientific
Different gear machining accuracy of vehicle gear drive system
In theory, the higher the gear machining accuracy level, the better the dynamic performance of the gear drive system, but […]
Scientific
Dynamic Stress of Drive Shaft of Vehicle Gear Drive System
The bending and torsional vibration displacements of the concentrated mass points on each drive shaft obtained by simulation are taken […]
Scientific
Bearing Support Reaction of Vehicle Gear Drive System
Bearing is the main component connecting the gear drive system and the box. Under the action of bearing support reaction, […]
Scientific
Load sharing factor of vehicle gear planetary drive
Under gear 1-8, the load-sharing coefficient of the loaded planetary row is shown in the figure, in gear 1-4, the […]
Scientific
No load gear dynamic load of vehicle gear transmission system
Previous studies have shown that the sound pressure of air radiation generated by no-load knocking of gears is proportional to […]
Scientific
Effect of Tooth Side Clearance and Center Distance Deviation of Involute Spur Gear on Dynamic Load
In gear meshing drive, in order to avoid jamming, clearance between tooth profiles must be left, which is an important […]
News
Study on dynamic characteristics of gear transmission system of tracked vehicle
For the gear transmission system of tracked vehicles, a nonlinear dynamic model of lateral torsional coupling is established. Combined with […]
News
Study on tooth profile modification of involute spur gear transmission system
Firstly, under the quasi-static condition, the influence of tooth profile modification parameters on meshing stiffness and load distribution coefficient between […]
News
Optimization software for static performance model of involute spur gear
ISIGHT software is a multi-disciplinary optimization software which integrates industrial optimization design and automatic analysis and calculation, which is introduced […]
News
Working Dimension Analysis of Helical Bevel Gear Fixture
Fixture positioning and fixture fixture fixture fixture is very important in the process of parts machining. If positioning is not […]
Scientific
Two parameter optimization design of involute straight tooth profile modification
The modification parameters of the two gears are the same, the value range of the modification amount is [0, 0.022mm], […]
Scientific
Time-varying meshing stiffness calculation of gear with cracks
Gao Yun used the finite element method to analyze the stress of gear, determined the position of the maximum principal […]
News
Optimum Design of Involute Straight Tooth Profile Reshaping
The relationship between dynamic load of gear drive system and modification parameters is very complex. When two or more modification […]
Scientific
Influence of Modification Types on Static Characteristics of Involute Spur Gear Drive System
The modification quantity is 0.22mm and the length is 2.8mm. The modification types are linear modification, parabolic modification and conic […]
Scientific
Effect of Profile Modification of Involute Spur Gear on Tooth Strength
In the research of tooth profile modification, the influence of tooth profile modification on the strength of gear teeth is […]
News
Three Elements of Profile Reshaping for Involute Spur Gear Drive System
There are three ways of tooth profile modification: cutting or grinding a part near the top of the tooth, which […]
Scientific
Effect of profile modification on dynamic load of involute spur gear under different profile modification lengths
With parabolic modification, the dynamic load coefficient changes with the modification amount under different modification lengths as shown in the […]
Scientific
The influence of the modification amount on the dynamic load of the involute spur gear transmission system with different modification length
Linear modification is adopted, and the value range of modification amount is [0, 0.05mm], and the value interval is 0.002mm. […]
News
Selection of Helical Bevel Gear Reference and Accuracy Determination
1 Selection of Rough Benchmarks The principle of choice is: (1) Non-machined surface principle. (2) The principle of minimum machining […]
Scientific
Modified tooth surface of helical gear under heavy load
TE at small wheel φ1A is smaller than LTE under larger load, indicating that the gap between teeth is not […]
Scientific
Test principle for vibration characteristics of planetary gear drive system
(1) Ring gear root strain test principle Eight teeth are selected as measuring points on the end face of ring […]
Scientific
Influence of External Load Change of Involute Spur Gear Transmission on Static Characteristics of Modified Gear
Linear modification is adopted with the modification quantity of 0.022m m and the length of 2.8m M. Fixed torque of […]
Scientific
Influence of Modification Length of Involute Spur Gear Drive System on Static Characteristics
Linear shape modification is adopted with the amount of 0.022mm. The value range of the length of the modification is […]
Scientific
Influence of Modification Amount on Static Characteristics of Involute Spur Gear Drive System
Linear shape modification is adopted with the length of 2.8mm and the value range of modification is [0.01mm, 0.09mm]. The […]
Scientific
Calculation of meshing stiffness and relative speed of helical gear meshing points
The meshing stiffness of the rodent point can be calculated by LTCA. The basic idea is to increase the load […]
Scientific
Profile modification length of involute spur gear drive system
In the research of profile modification based on static characteristics, the selection criteria of profile modification length mostly adopt the […]
Scientific
Research on Dynamic Characteristics of Gear Drive System under Steady State Conditions
Steady state condition refers to the condition under which the vehicle travels at a constant speed in a certain position […]
News
Time History and Spectral Analysis of Involute Spur Gear
The time history of each variable can be obtained directly by numerical integration. The response type of the system can […]
Scientific
Analysis Method for Nonlinear Dynamic Characteristics of Involute Spur Gear
There may be four kinds of motion forms in gear transmission non-linear system: periodic motion, double periodic motion, quasi-periodic motion […]
Scientific
Effect of No-load Speed of Involute Spur Gear on Dynamic Load
Under no-load condition, gear has two-sided impact phenomena and frequently falls out of teeth. Maximum dynamic meshing force and root […]
News
Standard Analysis of Service Process for Double Drive Gears
In order to guarantee the normal operation and use of the double gear effectively and facilitate material processing, the height […]